Design
An O-ring is an endless ring with a circular cross-section. Installed in a groove, it is squeezed between two surfaces; system pressure then pushes it against the low-pressure side of the groove and increases the sealing force.
In static service the O-ring is the most compact and cost-effective seal. At higher pressure or with a large extrusion gap, fit back-up rings. For reciprocating service where O-rings roll or spiral, consider T-seals.
Features
- Standard AS568 inch sizes and ISO 3601 metric sizes
- Hardness from 70 to 90 Shore A
- Oilfield compounds, including RGD-rated and sour-service grades
- Non-standard sizes and cross-sections made to drawing
- Batch number and cure date on every bag
Technical data
| Type | Static and dynamic (reciprocating) seal |
| Temperature | -40 °F to +600 °F, depending on compound |
| Pressure, static | Up to about 1,500 psi without back-up rings; higher with back-up rings, depending on gap and hardness |
| Speed, reciprocating | Up to about 1.6 ft/s |
| Hardness | 70 to 90 Shore A |
| Size standards | AS568, ISO 3601-1 |
Materials
| Compound | Hardness (Shore A) | Typical range (°F) | Typical oilfield use |
|---|---|---|---|
| NBR | 70, 90 | -30 to +250 | Hydraulics, crude oil, water injection, general service |
| HNBR | 75, 90 | -25 to +300 | Wellhead and valve seals, moderate H2S, RGD-rated grades |
| FKM | 75, 90 | -15 to +400 | High-temperature hydrocarbons, CO2, aromatics |
| FEPM (AFLAS) | 80, 90 | +15 to +450 | Amine inhibitors, steam, H2S, brines |
| FFKM | 75, 90 | +5 to +600 | Severe chemical and thermal service |
Ranges are typical and vary by compound. We confirm every recommendation against the actual compound datasheet.
RGD and sour-service grades
For gas service with rapid decompression, specify an RGD-rated grade, typically 90 Shore A HNBR, FKM or FFKM, qualified by test to NORSOK M-710 or ISO 23936-2. Small cross-sections resist decompression damage better than large ones.
For H2S service, HNBR suits moderate H2S and temperature; FEPM and FFKM cover more severe duties. NACE MR0175 / ISO 15156 applies to metals; for elastomers the relevant qualification standards are ISO 23936-2 and NORSOK M-710.
Specify for gas service
| Decompression | Rate (psi/min) and number of cycles |
| Gas | CO2, H2S and hydrocarbon content |
| Pressure | Maximum (psi) |
| Temperature | Range (°F) |
Sizes and standards
- AS568 dash sizes -001 to -475
- ISO 3601-1 metric sizes
- Non-standard inside diameters and cross-sections to drawing (tooling quoted separately)
Ordering information
Include the following in your RFQ:
- AS568 dash number, or inside diameter × cross-section in inches
- Compound and hardness, or the service conditions
- Quantity and required date
- Certificates required (EN 10204 3.1 as standard)
Applications
Wellhead & valves
Bonnet, seat, stem and connector seals
Downhole tools
Packers, sleeves, setting and completion tools
Flanges & connectors
Static face and radial seals
Pumps & compressors
Static and dynamic seals matched to the fluid
Hydraulics
Cylinders, valves and fittings
Need O-Rings?
Send the size or drawing, the service conditions and the quantity. We confirm a quote date when your request arrives.
