Home / Products / O-Rings

Static seals

O-Rings

Elastomer O-rings for static and dynamic sealing in wellhead, valve, pump and downhole equipment. Standard AS568 and ISO 3601 sizes, plus non-standard sizes made to drawing.

NBR, FKM and HNBR O-rings
NBR, FKM and HNBR O-rings

Design

An O-ring is an endless ring with a circular cross-section. Installed in a groove, it is squeezed between two surfaces; system pressure then pushes it against the low-pressure side of the groove and increases the sealing force.

In static service the O-ring is the most compact and cost-effective seal. At higher pressure or with a large extrusion gap, fit back-up rings. For reciprocating service where O-rings roll or spiral, consider T-seals.

Features

  • Standard AS568 inch sizes and ISO 3601 metric sizes
  • Hardness from 70 to 90 Shore A
  • Oilfield compounds, including RGD-rated and sour-service grades
  • Non-standard sizes and cross-sections made to drawing
  • Batch number and cure date on every bag
CSID / OD
Cross-section: O-ring: front view and cross-section (CS)

Technical data

TypeStatic and dynamic (reciprocating) seal
Temperature-40 °F to +600 °F, depending on compound
Pressure, staticUp to about 1,500 psi without back-up rings; higher with back-up rings, depending on gap and hardness
Speed, reciprocatingUp to about 1.6 ft/s
Hardness70 to 90 Shore A
Size standardsAS568, ISO 3601-1
Typical values. Actual limits depend on compound, gland design and service conditions; we confirm them on every quote.

Materials

CompoundHardness (Shore A)Typical range (°F)Typical oilfield use
NBR70, 90-30 to +250Hydraulics, crude oil, water injection, general service
HNBR75, 90-25 to +300Wellhead and valve seals, moderate H2S, RGD-rated grades
FKM75, 90-15 to +400High-temperature hydrocarbons, CO2, aromatics
FEPM (AFLAS)80, 90+15 to +450Amine inhibitors, steam, H2S, brines
FFKM75, 90+5 to +600Severe chemical and thermal service

Ranges are typical and vary by compound. We confirm every recommendation against the actual compound datasheet.

RGD and sour-service grades

For gas service with rapid decompression, specify an RGD-rated grade, typically 90 Shore A HNBR, FKM or FFKM, qualified by test to NORSOK M-710 or ISO 23936-2. Small cross-sections resist decompression damage better than large ones.

For H2S service, HNBR suits moderate H2S and temperature; FEPM and FFKM cover more severe duties. NACE MR0175 / ISO 15156 applies to metals; for elastomers the relevant qualification standards are ISO 23936-2 and NORSOK M-710.

Specify for gas service

DecompressionRate (psi/min) and number of cycles
GasCO2, H2S and hydrocarbon content
PressureMaximum (psi)
TemperatureRange (°F)
Test reports are supplied with RGD-rated compounds where specified.

Sizes and standards

  • AS568 dash sizes -001 to -475
  • ISO 3601-1 metric sizes
  • Non-standard inside diameters and cross-sections to drawing (tooling quoted separately)

Ordering information

Include the following in your RFQ:

  • AS568 dash number, or inside diameter × cross-section in inches
  • Compound and hardness, or the service conditions
  • Quantity and required date
  • Certificates required (EN 10204 3.1 as standard)

Applications

Wellhead & valves

Bonnet, seat, stem and connector seals

Downhole tools

Packers, sleeves, setting and completion tools

Flanges & connectors

Static face and radial seals

Pumps & compressors

Static and dynamic seals matched to the fluid

Hydraulics

Cylinders, valves and fittings

Need O-Rings?

Send the size or drawing, the service conditions and the quantity. We confirm a quote date when your request arrives.

Scroll to Top